Does anyone have a copy of firmware V 01.03.0509?

shockwave199 · Mar 15, 2018

I'm asking my question about the p4p, not the p4+.

RSS · Mar 16, 2018

u000gbk said:
I am very interested too as to the answer to this question. I currently run '509' in my AC and 1.1.3.0 in my +RC which is the latest version blessed by DJI for use in a +RC when running '509' in the AC ... so I would also like to know what later +RC version is compatible with '509' as well.

Hi

I'm also interested to know what's the higher RC firmware release that we can load in P4P+ remote control that can pair with AC firmware 0509
I have the same doubt about higher DJI GO 4 version that can works fine with P4P+ AC 0509

u000gbk · Mar 16, 2018

shockwave199 said:
I'm asking my question about the p4p, not the p4+.

Understood ... I also posed a similar question with regard to the + controller.

Timinator · Mar 16, 2018

Try it out as you don't have much to lose. Just make sure you have a copy of the original FW and a micro SD handy so if you need to reload the controller, you can. It's only controller software, folks!

MarkG_007 · Mar 22, 2018

Firebird said:
Index of /DJI-Firmware

use dumldore to get it back to 0509 ( i think 0304 is better). Then download 0300, delete the 306 module from within, flash 0300 (minus the 306 module), over the top of 0509. Now you should be on 0300-, & have all parameter tweaks plus the latest features (pano on p4p+ etc).

I tried that but got "Your flight altitude and distance has been limited" message which I believe is related to a mismatch between the RC and A/C firmware.

My current config.
Phantom 4 Pro
Aircraft Firmware : V 01.03.0509
Remote Controller Firmware : V 1.4.1.0
DJI GO 4 App iOS : V 4.1.12
Apple ipad mini 4 ios 11.2.6

Am I doing something wrong? Any suggestions? Tks. Mark.

Firebird · Mar 22, 2018

need to log in the dji app

MarkG_007 · Mar 22, 2018

Firebird said:
need to log in the dji app[/QUOTE

Yes. I did that several times. Still had alert msg. Am going to try with DJIgo4 4.0.8

Firebird · Mar 23, 2018

i just tried 0509, GO412 and RC 1.4.10. works fine. Could just be a bad flash? I would try again.

Firebird · Mar 23, 2018

running iphone 10 with 1126

MarkG_007 · Mar 23, 2018

Firebird said:
running iphone 10 with 1126

Thanks. Just reflashed and working with go 4.0.8. Will try go 4.1.12 next. Which I believe is as high as I can go and retain the 32 ch mod. Appreciate the assistance.

Firebird · Mar 23, 2018

good news Mark. Well done mate.

MarkG_007 · Mar 31, 2018

Firebird said:
good news Mark. Well done mate.

Just as a follow up. I’ve done a bit more experimenting.
Going from go 4.0.8 to go 4.1.12 resulted in the alert msg returning. (Just doesn’t like 4.1.12)

So working config is. Fw 1.03.0509 with go 4.0.8

Also got mixed modules to work with 03.0509 and 04.0602 on top. (Providing parameter adjust and 32 ch)
Mixed 05.300 which also worked but has the inverted image prob.
Can’t find a copy of 05.600 to try. (Yet)

Tks for your help.