I remember something about inspecting the item.Don't know if you can do that .
I remember something about inspecting the item.Don't know if you can do that .
You might can I just have never done it . You should be able to though .I just never have and really don't know if they will wait .I remember something about inspecting the item.
I'll give the driver a bottle of waterYou might can I just have never done it . You should be able to though .I just never have and really don't know if they will wait .
One way to see though![]()
I have sma connectors for the helicals...it sux cuz the center pin is too short on these fir the china ones...ill let you know which ones to get.Pro where did you get the cable adapter to witch the antennas over.
Ok thanksI have sma connectors for the helicals...it sux cuz the center pin is too short on these fir the china ones...ill let you know which ones to get.
Procharged, I looked into an RF meter because I thought I had a bad uFL cable.I have sma connectors for the helicals...it sux cuz the center pin is too short on these fir the china ones...ill let you know which ones to get.
Oh I used the wrong 4 post sma to solder on these china panels....but I do have issues I just found from my cables inside the rc... I have the rg402 cables and was taking them off and on and didn't notice I spun them...now my signal is intermittent which sucks cuz I have a lot of stuff I want to test but have to wait a few weeks now to order some u.fl cables since the mmcx wont work.Procharged, I looked into an RF meter because I thought I had a bad uFL cable.
I actually ended up twisting it so much that it broke. I replaced all new cables, but I wouldn't mind having one to check if I have a good signal without opening the controller.
How do you like yours? I looked into this one, but decided to hold off.
http://www.amazon.com/Cornet-ED78S-...00P67QLA0/ref=cm_cr_arp_d_product_top?ie=UTF8
I'll see if I got any extras laying around, I think I need to order some too. Anybody else got any of these extras laying around we can send to procharged? If I don't have any I'll order a 10 pack and send you a fewOh I used the wrong 4 post sma to solder on these china panels....but I do have issues I just found from my cables inside the rc... I have the rg402 cables and was taking them off and on and didn't notice I spun them...now my signal is intermittent which sucks cuz I have a lot of stuff I want to test but have to wait a few weeks now to order some u.fl cables since the mmcx wont work.
I got my Immersionrc rf power meter Saturday and tried it but its defective lol so I have to wait to get a replacement or repair...sucks. I will let you know how it is tho when I get my replacement! I'm going to look up the one you put a link for
What aircraft are you intending on using it for, and what are your long range or penetration goalsSince I have been reading a lot of the post in this sub channel. I have a question which would you say is better to get, The ITelite antenna or the FPVLR circular antenna?
I am using a P3S I would like to get 4000 meters.What aircraft are you intending on using it for, and what are your long range or penetration goals
I'm getting that with my panel, not boosted just the dbs panel.I am using a P3S I would like to get 4000 meters.
Please post pictures. Plus pictures of type of ground you are flying over. (Houses, land, water, etc etcI'm getting that with my panel, not boosted just the dbs panel.
Please post pictures. Plus pictures of type of ground you are flying over. (Houses, land, water, etc etc
here is another, little shorter depends on wind and clouds...Oh I beleive that over that type land! Not a house or power line in sight! I wish we had that in my part of florida! All I have is trees, houses, and power lines.... ugh
We use essential cookies to make this site work, and optional cookies to enhance your experience.