Hello, I was gifted a crash Phantom 4 pro V 2.0 When I turn the drone it self on a red and green light flashes for a few sec and then 2 solid red lights at the same time its beeping continuously. the original owner let the camera hit something and broke off. I replaced the camera it showed up on the remote normal and it seems to respond ok but I tried a Firmware update and it errors out at 34% DJI told me send it in but I would rather fix it my self any ideas I would greatly appreciate it (Remote firmware update normal)
Phantom 4 Pro Plus V1 drone beeps continuously (not controller) Firmware update stops at 34%
- Thread starter illistmike80
- Start date
Very possible there may be an internal board that isn’t happy.
A bit more specific info on what you have(p4p V2 plus?) and what you have done to it will help all that are reading this.
Just for reference, a V2 will have a gold DJI sticker on top center of aircraft and the controller will have vent holes in the bottom section.
A bit more specific info on what you have(p4p V2 plus?) and what you have done to it will help all that are reading this.
Just for reference, a V2 will have a gold DJI sticker on top center of aircraft and the controller will have vent holes in the bottom section.
Thanks for the reply I think it is the V2 I will add pictures if it helps
When i got the drone it had no camera it broke off during the initial crash with original owner
I bought a replacement switched it out and it showed up on the remote perfectly fine
I did the firmware update on both control and drone the control completed put the drone stop at 34%
Here's a video of it
drive.google.com
When i got the drone it had no camera it broke off during the initial crash with original owner
I bought a replacement switched it out and it showed up on the remote perfectly fine
I did the firmware update on both control and drone the control completed put the drone stop at 34%
Here's a video of it
20210130_011508.mp4
drive.google.com
Attachments
You have a phantom4 pro plus V1. Should read GL300 E on the controller. Based on these pictures, this aircraft took a very hard hit.
It is possible that some form of repair will resolve the issue that you’re having, but probably will need more than what you can provide. Do you have the rest of the original camera?
It is possible that some form of repair will resolve the issue that you’re having, but probably will need more than what you can provide. Do you have the rest of the original camera?
Oso
Premium Pilot
@illistmike80 - As noted, it’s not a V2. WM331A is the model number for the P4P. I believe the V2 is WM331S if I recall correctly.
At least it was a gift and you didn’t pay a V2 price.
@Starz - are the V1 and V2 cameras interchangeable? I don’t know much about P4s, so please forgive me if it’s an obvious answer. I was wondering if that could have stalled the FW update. ?
At least it was a gift and you didn’t pay a V2 price.
@Starz - are the V1 and V2 cameras interchangeable? I don’t know much about P4s, so please forgive me if it’s an obvious answer. I was wondering if that could have stalled the FW update. ?
Yes, V1 and V2 cameras are basically the same. I have seen a post that mentioned some slight variation of some internal components that were different but didn’t seem to have any real noticeable performance difference. On the above aircraft, I’m thinking there are more issues here than just a camera swap.
Thanks you both for replying I really appreciate the help
@Starz No the camera didn't come with it
So what do you recommend I do from here is it worth investing in I know DJI is going to charge a whole lot
and I already put $600 in replacing the camera my initial plan is to get a Mavic air 2 or a Mavic pro 2
should i sell it as is with a need hardware repair with pictures and video or do I send it to DJI for repairs hoping its not to expensive and then sell it
am not interested in the extra cash as long as I can get a Mavic?
@Starz No the camera didn't come with it
So what do you recommend I do from here is it worth investing in I know DJI is going to charge a whole lot
and I already put $600 in replacing the camera my initial plan is to get a Mavic air 2 or a Mavic pro 2
should i sell it as is with a need hardware repair with pictures and video or do I send it to DJI for repairs hoping its not to expensive and then sell it
am not interested in the extra cash as long as I can get a Mavic?
There are other options besides DJI for repairs. Any possibility of returning the camera for a refund?
Contact this guy @Droneted
Contact this guy @Droneted
Last edited:
I tried both ways but no sure about the version can you elaborate a lil more please
thank you will try also i am in comunication with @Droneted now
Imu calibration is based on an intact airframe. By looking at the pictures, that may not be the case here.
- Joined
- Dec 4, 2018
- Messages
- 148
- Reaction score
- 33
- Age
- 60
- Location
- Missouri City
- Website
- www.dedroneservice.com
- Joined
- Dec 4, 2018
- Messages
- 148
- Reaction score
- 33
- Age
- 60
- Location
- Missouri City
- Website
- www.dedroneservice.com
Then restart your Phantom 4 Pro V2.0 and do the same thing with the remote control update it from your computer or laptop then restart it
It’s not a V2. And probably not a firmware issue if you look at the pictures and associated crash damage.
Note: I’ve been wrong before, but I don’t think that’s the case on this one.
- Joined
- Dec 4, 2018
- Messages
- 148
- Reaction score
- 33
- Age
- 60
- Location
- Missouri City
- Website
- www.dedroneservice.com
DJI Assistant 2 Version 2.0.10 is for the Phantom
DJI Assistant 2 Version 2.0.14 is for Mavic
be sure you are using 2.0.10 or it won't even recognize the bird
DJI Assistant 2 Version 2.0.14 is for Mavic
be sure you are using 2.0.10 or it won't even recognize the bird
Similar threads
