P2+ TX Mod with Inspire1 tab mount

[G-unit]

I really liked the inspire1 tab mount so i did a mod to my P2+ TX and put it on it, way better then the other options. I used a 1/4-20 nutsert for the mount to screw in, I think it turned out good..

 

[battman2036]

very clean.

 

[G-unit]

Thank You..

 

[battman2036]

what did the mount set you back? any issues with it blocking your control sticks?

 

[G-unit]

what did the mount set you back? any issues with it blocking your control sticks?

Hi, it was $22 on ebay, there is no blocking at all ,Its like it was made for it.

 

[jetlag]

I really liked the inspire1 tab mount so i did a mod to my P2+ TX and put it on it, way better then the other options. I used a 1/4-20 nutsert for the mount to screw in, I think it turned out good..

I would like to do the same to use an 8.9" kindle fire unit and my P2v+ TX. Could you elaborate a little on the nutsert and what and how you drilled the case. I am afraid my technical skills are not nearly as good as yours and would hate to destroy the case. Also what is the mount called so i can look it up on Ebay. Thank You

 

[Jan Erik]

I would like to do the same to use an 8.9" kindle fire unit and my P2v+ TX. Could you elaborate a little on the nutsert and what and how you drilled the case. I am afraid my technical skills are not nearly as good as yours and would hate to destroy the case. Also what is the mount called so i can look it up on Ebay. Thank You

I used this mod on my P2 also :

http://www.ebay.com/itm/DJI-Inspire...055?pt=LH_DefaultDomain_0&hash=item2c989249ff

 

[jetlag]

I used this mod on my P2 also :

http://www.ebay.com/itm/DJI-Inspire...055?pt=LH_DefaultDomain_0&hash=item2c989249ff

Thank You. How and what did you use to drill the case?

 

[Jan Erik]

Thank You. How and what did you use to drill the case?

Just drill a hole that is a little smaler than the screw. I did find the position by holding the bracket sideways...left and right. Then make a pencil mark at both positions,and draw a line..... Then hold it in the center.... I did only use a little bit force and screwed it into the controller.... just remember that the wires inside goes straigh under it ...;-)

 

[Jan Erik]

Mod for my Samsung Tab S 10.5" to "fit" on the Inspire 1 Holder

 

[jetlag]

Mod for my Samsung Tab S 10.5" to "fit" on the Inspire 1 Holder
View attachment 18470

Looks very nice

 

[DBS]

cool solution right there... i'mma give this one a shot

 

[jetlag]

cool solution right there... i'mma give this one a shot

And If you would post a how to video I will be very grateful. lol.

 

[G-unit]

It is very easy to do..

 

[jetlag]

It is very easy to do..

Yes, until I start drilling holes, lol.

 

[G-unit]

Yes, until I start drilling holes, lol.

LOL.. just start with with a pilot hole first,"Small Drill" then work your way up to the right size.

 

[jetlag]

LOL.. just start with with a pilot hole first,"Small Drill" then work your way up to the right size.

Thanks I may end up there anyway if this doesn't work. I found this here on the site. If it does not work, I am out 40 bucks and will be forced to drill holes. Here is the mount I found:
Satechi® Dashboard Mount Universal Tablet Car Mount Holder (for 8.9" - 11" Tablets) iPad, Nexus 10, Samsung Galaxy Tab 8.9", Samsung Galaxy Tab 10", S

 

[G-unit]

Thanks I may end up there anyway if this doesn't work. I found this here on the site. If it does not work, I am out 40 bucks and will be forced to drill holes. Here is the mount I found:
Satechi® Dashboard Mount Universal Tablet Car Mount Holder (for 8.9" - 11" Tablets) iPad, Nexus 10, Samsung Galaxy Tab 8.9", Samsung Galaxy Tab 10", S

What Tx do you have, The new one with the tilt wheel on the side or the old one ?

 

[jetlag]

I have both since I have had my P2V+ from early on. I am using the new TX right now

 

[G-unit]

Well i was going to offer to help, I have a old Tx shell that i could drill for you and swap the covers, but you need the new Tx,