lets say just in theory that someone went 3000 ft in the air and decided to hit the csc command and let it fall a thousand feet and then hit the csc to turn it on again. what would happen? if the drone ended up falling upside down would it correct itself if in gps mode? how long would it take to recover, how likely, thanks
CSC Command
- Thread starter notsolowki
- Start date
- Joined
- Jan 3, 2016
- Messages
- 681
- Reaction score
- 56
- Age
- 55
The answer is most likely no. It wouldn't make it. BUT I've seen a video on YouTube around a year ago where a guy was experimenting this in his backyard and out of around 10 tries, ONCE he actually was able to restart it in midair.
Sent from my SM-G900FD using PhantomPilots mobile app
Sent from my SM-G900FD using PhantomPilots mobile app
wouldnt it restart if i hit the csc command? or is it that its in the air and the programming wont allow it to start in the air?
- Joined
- Dec 18, 2016
- Messages
- 331
- Reaction score
- 71
- Age
- 58
I think it would restart and providing its the right way up it should be ok depending on how close you were to the ground on restart but I wouldn't try it though unless I was very rich and could afford to try thinks like that and didn't mind trashing a few
If I'm seeing it right in that video the thing is upside down when he restarts it
it looked promising. it also looked like it took all that altitude to complete. i just wonder suppose it started twisting or flipping violently if it could pull out of it
- Joined
- Dec 18, 2016
- Messages
- 331
- Reaction score
- 71
- Age
- 58
Only way to know for sure would be to try it, not me though lol
My cheap Syma XC5 can do this. It's interesting if the Phantoms can't, but I can see the weight difference being an issue.
- Joined
- Jan 3, 2016
- Messages
- 681
- Reaction score
- 56
- Age
- 55
I thought CSC shuts down the drone entirely, not only motors. So you could watch the freefall. What a sadism 
)
Sent from my SM-G900FD using PhantomPilots mobile app
)Sent from my SM-G900FD using PhantomPilots mobile app
the other day iw as flying my drone and decided to fly above the log fog clouds. soo i noticed i was 5000 ft away when i was supposed to be more like 20 ft away. i thought for sure it was a goner because of the 30 mph wind gusts. thankfully i made it back with 2 percent battery to spare. the scariest part was ascending with 3 percent battery to spare from 500m i was really close to restarting it in the air to loose some altitude but i didnt. 1200ft away 500m 13 percent battery
- Joined
- Dec 18, 2016
- Messages
- 331
- Reaction score
- 71
- Age
- 58
My Phantom 3 Pro is back from having a new gimbal fitted under warranty. I'm testing it inside without props and have found that if I pull the left stick fully down for a few seconds the aircraft turns itself off!! I thought that a CSC had to be used to turn the aircraft off. What's to say that while I'm flying, I do the same and stall the aircraft. WTF!!!
You need to read the manual. Holding the left stick back only kills the rotors once it's landed.
- Joined
- Dec 24, 2016
- Messages
- 409
- Reaction score
- 117
Pulling the left stick down for a few seconds (while on the ground) will turn off the motors because the craft doesn't detect a decline in altitude. It's the simplest way to land.
If you pull the left stick down while in flight the motors will not stop. The CSC command to shut off the motors is now left stick inner lower corner and RTH button at the same time. At least that's what it is on the Phantom 4.
Last edited:
msinger
Approved Vendor
- Joined
- Oct 30, 2014
- Messages
- 32,156
- Reaction score
- 10,917
- Location
- Harrisburg, PA (US)
- Website
- phantomhelp.com
The CSC command has not changed for the P3P. However, if you're running the latest firmware, you have to hold the CSC position for 3 seconds in order to kill the motors mid-flight.
