repair

Due to my own inattention, I crashed my P4P into the side of my house a while back. One landing gear was broken off on both sides from the lower shell and the lower shell was damaged. Given things I had heard about DJI service and given that I wasn't making a warranty claim, I decided to send it...

When I look at the status of my DJI repair order online at their site, the status times are shown in the future! It says the product was received on Feb 16, 2017 at 12:10 AM. It also says that the issue was verified on Feb 16, 2017 at 01:14 AM. My first thought was that this is UNC time...

Hey all, Looking for some guidence on repairing/replacing the front left camera on a crashed Phantom 4. This is one of the cameras used for obstactle detection. When the drone crashed, the main power connector broke off the main circuit board and tore the ribbon cable going to one of the...

Hi all, I've only had my phantom 3 for 2 months and I made the fatal mistake I hear a lot of there make. Accidentally putting the long prop guard screws in without the prop guards resulting in ruined motor coils. So I ordered all four of my new motors, made sure they were the exact ones I...

In the unfortunate case you crash your drone or however it gets damaged, I'm here to fix it for you! My passion is building drones, upgrading systems, and fixing them when needed. I have worked on a variety of brands and models. So if you want to get your UAV back in the air, I'm here to help...

So this happened. When I get the new part in does anyone know how that ring goes on? It looks like it had glue applied and then pressed on, hard to tell. Anyone had to do this repair yet? Also the camera housing got banged up a little. Anyone know where I can get just the housing or if...

does anyone know where to physically buy a flat gimbal cable near the Lake Tahoe area? Thanks.

not sure if the link is published, but the DJI self service area is pretty handy! https://repair.dji.com/en/SelfRepair/Area

Hey All! Well I have developed some sort of crack on the top of my bird by the motor [see attached picture]. I just sent my bird [P3P] into DJI for repair yesterday, hopefully it will be free as that is what I have heard most others being. But most stress cracks I have seen pictures of...

I crashed my drone recently (clipped a tree). The shell is damaged and will need to be replaced. Does anyone have rough estimate of how much this will cost to repaired if I send back to DJI? I see that the shell runs about $59. I don't really think this is something I would be OK with...

When Dji states that you have unlimited repairs (if it comes within coverage ammount) does the coverage balance reset or will it be deducted as the repairs come and go, so doesn't it mean it isn't unlimited I'm confused when the repair coverage is deducted will it eventually run out or will it...

So I was flying my Phantom up a road on a hill and did something stupid, which was to turn a curve around the mountain and the Phantom got disconnected. I wasn't too worried as I'd set it to a return home altitude that was way more than enough, but when I ran around the corner I couldn't find it...

Hi, My name is Daniel Smirnov with Smirnov's Computer Repair located in Carmel. I'm an Informatics Major, have consistently been on the Dean's list, and am TestOut PC Pro Certified. We've been repairing and building all types of tech for years. Be it drones, printers, TV's, computers, you...

I crashed my p3a into a tree yesterday, and it is totally my fault. After I reboot everything, the motor num2 doesn't work anymore, and a motor obstructed error message popped up. Even though that motor rotates just as fine as others, I was still hoping the motor itself was broken during the...

Hey guys! So, I'm creating this post both to share a mildly entertaining story, and to glean some information that I need from the community. My questions are highlighted near the bottom. So let's get started... So I just got back from Mexico this week. I did a lot of flying, and captured a...

Hi. I crashed my drone, and the compass connector snapped off. Im planning to solder it back on, but just want to know if any of you have any experience with soldering on a p3? Planning to buy a 30w iron, and 0,53mm 60/38 solder with 2%flux. I can see that there are 5 points to solder. Can i...

My Phantom 3 Standard crashed a few weeks ago and sent it in for repair. Just got it back, and it's up and running. They lived up to their reputation for horrible support (It took a week and multiple phone calls to get the invoice that they promise to send in 24 hours). However, they ended up...

Hello, I am planning to repair my P3P and am seeking advice. I'm not sure if I need a complete gimbal or only parts for the repair of the gimbal. I am also in the Tuscany area of Italy and am not sure where to source parts. I see very knowledgable people on this forum and any advice would be...

Hi. Does anyone know if replacing the prop motors on P4 uses same, simple procedure as its predecessors or is it more complicated? I've had good luck, never had to open mine or done any mods to it. This morning I had an 'incident'. Overall bird is fine but one motor seems to lag a bit. I'll...

Hey everybody... Crashed my P4 last week, completely ruined the Camera Gimbal unit. I ordered a replacement from DJI, but the power connector seems to have 5 pins... My old camera unit had 4 pins... Anybody know what this is about?