Recent content by Flying Brian

Cool :)

Well, sandman, if you read the whole thread, you might realize that I have spent less than $250 for a decent AP. That doesn't have any limitations as far as geofencing and have the manual mode. If you've got more money than you need then spend spend spend. But don't assume you know the...

Jason, I've got the SR6 stock Phantom 1 controller with the tilt control on a lever on the lower back of the controller. With the cheap 2d gimbal I was using the output from the Naza to control tilt and I could adjust the dampening. There's gotta be a way of doing this. Thanks Brian

I wasn't, but now I am and still can't find the firmware. I'm going to the H3-3D page and the only firmware there is Zenmuse Assistant 1.12. When I install it, it says it is version 1.4. That won't connect either. Can you link me to the firmware? Thanks SOOO Much Brian

Hey Jason, Should I be using the P2 assistant with this P1 upgrade board? Or does that pic say P2 because that is what you have plugged into it? I have the Naza-M v2 But when I change the manual control speed for pitch (x1), it doesn't change the speed. This is the upgrade screen it shows me...

Well, thanks to your help Jason, I was able to get everything working. The one problem I have is adjusting the gimbal pitch speed. It has no dampening. Do you know what software to use to adjust the gimbal? I tried the assistant 2.20 and 2.40 and the Zenmuse assistant, but none of those will...

Yes I saw that, but I thought that was for the P2 board. Do you know they are the same pinouts as the upgrade board? With my header being 90 degrees to the P2 board I don't know that they are the same. And you are using 4 wires and the upgrade instructions only mention 3 wires. Thank You Brian

Hey Jason, I'm using the stock controller, the SR6 tx. I'm wondering if I can check the pinouts on that 6 pin molex for vid out on the upgrade board. Cheers Brian

Hey Jason, That must be a P2 board. The upgrade board is a little different see below. But what you said in your last msg is the info I was looking for. The pinouts on the upgrade board not the vtx, I already had that working with the 2d gimbal. What has changed is now I'm installing the H3-3D...

H Jason, I'm using a Team Black Sheep 5.8 tx. The problem I have is the connection to the upgrade board. The tiny picture in the instructions is not clear enough to see the pinouts on that header that goes to the vtx. Do you know is that plug called a molex? 6 pin? Thank you Brian

Hey Guys, I've got a P1 with a P2 bottom shell and the upgrade board and the canbus hack so I could use the miniOsd. And I'm using a TBS 5.8 tx on the bird and I'm trying to install the H3-3D gimbal. I also have the P2 signal hub v1. Am I to use this hub? Or do I come off the upgrade board...

Well, looks like it wasn't the best deal. When I went to pick up the gimbal, the box had been opened and the GCU was missing. I checked another Frys and the same thing. I guess someone was stealing the GCU's out of these and returning them to the store. Well I think I don't need it with the...

Hi Bill, I didn't know that the H3-3D gimbal could be had for so little. After your suggestion I looked and found one at a Fry's store for $129! I thought they were a lot more costly. I think you've made up my mind. Thanks so much for the fast reply and the suggestion. Cheers Brian

Hey guys, Looks like my cheap 2d gimbal is dead. I've been checking out the 3d gimbals. I had a question for the more knowledgeable brains here(at least more than mine). Which of the sub $100 3d gimbals would you get for the P1 with the upgrade board? Thank You Brian

Hey gianni, What I meant was that the upgrade board has a 6 pin power header that is described as for a vtx, an 8 pin header for the H3-2D gimbal, and there is also a 2 pin header that says reserved. I was wondering if anything was ever done with that header. I thought I'd use the vtx header...